Perth Craft Fair and Quilt West: 2013

27 05 2013

I spent yesterday at the Perth Craft Fair and QuiltWest exhibition. My feet were sore by the end of the day, but it was so inspirational that many of the issues just getting to the Perth Convention Centre disappeared fairly rapidly.

The main issue was that, without any notice, the organisers of the ‘HBF Run for a reason’ event closed The Esplanade from Spring St AND closed the Convention Centre car park until 11 am. All info I had prior to that event was that The Esplanade would be closed from Mill St. Even the trade exhibitors were caught with the closure of the car park at 7:30 am. And it seems the trains didn’t stop at the Convention Centre for some hours either (again, without notice as far as I could tell) — they went on to Central so anyone catching the train had to walk from the city station back to the Convention Centre. Not good for anyone with mobility issues who had deliberately caught the train to be dropped right at the Convention Centre.

Parking was at a premium as the city centre was host to 30,000 runners, but I eventually parked the car up behind Parliament House! My friend Joan and I had a long downhill walk to the Convention Centre…

Back to the Fair… The big plus of those road, train, and car park closures was that the Convention Centre was almost empty of everyone except officials and stallholders for the first couple of hours, which meant we could get around without bumping into other people or being forced to move on because of the pressure of crowds. And we could get to speak to stallholders and view their products without hindrance. And get a seat at some of the free demos.

The highlight of the event was the QuiltWest exhibition, which highlighted some of the stunning work by local quilters, and had on display the Australian winners of a national competition, and some from a South Australian competition. And there was a big display of community quilts— many of which I recognised as I’d quilted them 😉

I took a heap of photos on my camera phone, so the quality of the images is not particularly good. I tried to capture the essence of the works, but of course, the exquisite detail is lost. I didn’t record any information about each quilt, so here are the photos, not in any particular order.

IMAG0795

IMAG0796

IMAG0797

IMAG0798

IMAG0799

IMAG0800

IMAG0801

IMAG0802

IMAG0803

IMAG0804

IMAG0805

IMAG0806

IMAG0807

IMAG0808

IMAG0809

IMAG0813

IMAG0734

IMAG0735

IMAG0736

IMAG0737

IMAG0738

IMAG0739

IMAG0740

IMAG0741

IMAG0742

IMAG0743

IMAG0744

IMAG0745

IMAG0746

IMAG0747

IMAG0748

IMAG0749 IMAG0750

IMAG0751

IMAG0752

IMAG0753

IMAG0754

IMAG0755

IMAG0756

IMAG0757

IMAG0758

IMAG0759

IMAG0761

IMAG0762

IMAG0764

IMAG0765

IMAG0766

IMAG0768

IMAG0769

IMAG0770

IMAG0771

IMAG0772

IMAG0773

IMAG0774

IMAG0775

IMAG0776

IMAG0777

IMAG0778

IMAG0779

IMAG0780

IMAG0781

IMAG0782

IMAG0786

IMAG0787

IMAG0788

IMAG0789

IMAG0790

IMAG0792

IMAG0793

 

 

 

 





Handy Quilter Sweet Sixteen: Fixing a loose top spool holder

27 05 2013

My Sweet Sixteen is just over two years’ old and has had a decent workout (nearly 9 million stitches and counting!). When I took it in for the light ring change out a couple of weeks back, I noticed that the top spool holder was loose. The thread seemed to be stripped from the screw-in part. My rear thread mast was fine, but my dealer did say that she knew of some that were also a tad loose as the thread seemed to be stripped from them.

My solution was a $2 roll of plumbers’ tape from the hardware store! I think I have enough tape to last several lifetimes as I only used a tiny bit to wrap around the screw-in part of the top spool holder, and there seems to be an awful lot more on the roll.

It worked beautifully. The top spool holder is now firm where it screws in to the machine–no more wobbles!

I also put a tiny bit of plumbers’ tape on the thread mast screw-in bit too, just in case.