New soakwell

31 05 2017

When our house was built, there was a ‘secret gutter’ in the roof, which caused no end of problems because the builders didn’t put in a downpipe to redirect the flow off the roof to a soakwell. Instead, the water gushed into the end of a normal gutter and had to find its way to the other end before going down a downpipe. It was a real problem when we had heavy rains, because the water would spill over the end of the gutter and fascia board and get under the eaves, thus causing mould on the eaves and a very wet fascia board. The mould was how we knew there was a real problem with the roof design. And I learned there was a such a thing as a ‘secret gutter’!

Our wonderful handyman was able to identify the issue a few years ago, and he and his roof plumber mate fixed the secret gutter flashing and added a downpipe so the water had somewhere to go. However, water from the downpipe just spilled onto the concrete, not into a soakwell. This caused some further issues, with water pooling on the concrete and algae forming over time (in the scheme of things, these were just minor issues). I added a spoon drain at the end of the downpipe as as a temporary measure to redirect the flow further out onto the concrete pad, but I knew at some point we’d have to get the water redirected into a soakwell.

Twelve months ago, my handyman cut open the concrete pad and installed a drain into the garden for another issue (a small dip in the concrete pad where water accumulated), so I asked if he could do something similar at the end of the downpipe, and install a soakwell. Yep, anything is possible for this guy (he’s an absolute keeper!).

He and his helper spent half a day cutting into concrete, digging a graveyard-size hole in the lawn (fortunately missing the retic pipes!), digging a trench under the concrete, installing a drain pipe and drain cover, and installing a ‘open weave’ heavy-duty plastic soakwell (after wrapping it in several layers of geotextile fabric). They then packed the dirt back in, put the lawn back, and went on their way.

It works a treat! The water from the downpipe now goes into the drain and into the soakwell, so no more trip hazards with spoon drains and algae!

 





Community Quilt 327

31 05 2017

Another scrappy quilt, with lots of patterns and colours competing for attention. I decided to quilt it with an all over ‘squared off’ open-headband motif, in a blue/teal coloured thread.

(Click on a photo to view it larger)

Threads used:

  • Top: Robison-Anton ‘Wonder Blue’ (40 wt, rayon, colour 2577)
  • Bottom: Fil-Tec Magna Glide Classic pre-wound bobbin (lead gray)

 





Community Quilt 326

4 05 2017

How to quilt this very angular quilt? I decided to counter all those angles with some circles — in this case, large bubbles in a continuous line, extending into the border.

(Click on a photo to view it larger)

Threads used:

  • Top: Fil-Tec Glide ‘Celery’ (40 wt, trilobal polyester, colour 60580)
  • Bottom: Fil-Tec Magna Glide Classic pre-wound bobbin (white)

 





Community Quilt 325

4 05 2017

After stitching in the ditch around the big banner blocks, I decided to do some simple straight line ruler work in the blocks. I stitched three banners horizontally — stitching in the ditch in the seams and across the centre of the fabric; and two banners vertically. I left the borders and sashing unstitched.

(Click on a photo to view it larger)

Threads used:

  • Top: Superior King Tut ‘Passion Fruit’ (40 wt, cotton, colour 931)
  • Bottom: Fil-Tec Magna Glide Classic pre-wound bobbin (light tan)

 





Community Quilt 324

4 05 2017

Someone spent a lot of time doing the redwork embroidery for each of the alphabet letters in this quilt. I just hope they washed the red embroidery thread and the border fabric very well before making it, otherwise there’s a good chance the red will run into the cream when this quilt gets washed. As I was quilting it, I could see quite a few red thread tails behind the cream blocks — if the dye runs, it will ruin this lovely quilt.

How to quilt it? I started by stitching in the ditch around each block and the outside of each letter. Then I did a smallish stipple in the ‘white space’, which lets the letter pop out, almost like trapunto. I left the red sashing strips and borders unstitched.

(Click on a photo to view it larger)

Threads used:

  • Top: Fil-Tec Glide ‘Linen’ (40 wt, trilobal polyester, colour 20001)
  • Bottom: Fil-Tec Magna Glide Classic pre-wound bobbin (white)

 





Community Quilt 323

4 05 2017

For this quilt, I decided to counterbalance the square and angled geometric shapes with large overlapping spirals, using a variegated brown thread.

(Click on a photo to view it larger)

 

Threads used:

  • Top: Signature ‘Woodlands’ (40 wt, cotton, colour SM003)
  • Bottom: Fil-Tec Magna Glide Classic pre-wound bobbin (light tan)

 





Community Quilt 322

25 04 2017

To enhance the diagonal pattern of this quilt, I stitched straight lines every two diagonal rows, then stitched a large meandering stipple in the main border, leaving the pink and green borders unstitched.

(Click on a photo to view it larger)

Threads used:

  • Top: Fil-Tec Harmony ‘Driftwood’ (40 wt, cotton, colour 14069)
  • Bottom: Fil-Tec Magna Glide Classic pre-wound bobbin (light tan)

 





Community Quilt 321

25 04 2017

How to quilt this ‘asterisk’ quilt? I started by stitching in the ditch around all the blocks and the asterisk elements (including their square centres), then did a small stipple in the background for each asterisk. I finished with a large stipple in the border and diagonal stitching in the small squares in the border. I left the asterisks, the green border, and the bars of solid colours unstitched.

(Click on a photo to view it larger)

Threads used:

  • Top: Robison-Anton ‘Coffee Bean’ (40 wt, rayon, colour 2339)
  • Bottom: Fil-Tec Magna Glide Classic pre-wound bobbin (lead gray)

 





Community Quilt 320

25 04 2017

I went back to one of my ‘muscle memory’ motifs for quilting this quilt — a flower variation of ‘open headbands‘. Instead of finishing the final arc with a curved arc, you hop back with little arcs that look like petals on a flower.

(Click on a photo to view it larger)

Threads used:

  • Top: Gutermann (40 wt, polyester, colour 800)
  • Bottom: Fil-Tec Magna Glide Classic pre-wound bobbin (white)

 





Community Quilt 319

25 04 2017

There were lots of very busy fabrics in this quilt, so I quilted it in an all-over motif — a meandering stipple, punctuated with circles. I repeated this motif in the pink border too, leaving the white border unstitched.

(Click on a photo to view it larger)

Threads used:

  • Top: Fil-Tec Glide ‘Pink’ (40 wt, trilobal polyester, colour 70189)
  • Bottom: Fil-Tec Magna Glide Classic pre-wound bobbin (white)