Using the Line Tamer ruler with the Handi Quilter Sweet Sixteen

28 01 2013

I haven’t done much ruler work with my Sweet Sixteen, with the exception of straight line work (e.g. stitch in the ditch) using the Line Tamer ruler from Four Paws Quilting. I love this ruler as it has channels to hold the hopping foot in place and so there’s very little that can go wrong — for example, it’s not easy to wander off line if you use it correctly.

However, I initially had a few trials and errors in using it, so this short tutorial shows you how I use it and what to watch for so that you can keep your stitching lines nice and straight.

PLEASE NOTE: This ruler is NOT for use with domestic sewing machines — it is made specifically for mid-arm and long-arm quilting machines and it comes in two sizes, depending on the machine you have.

First, let’s take a look at this ruler (click on a photo to view it larger):


The ruler is 10.5 inches long, with vertical lines laser-etched into the plastic every 0.5 inches. There are two horizontal lines — the top one near the opening is 1.5 inches down from the top, and the bottom one is 1.75 inches from the base of the ruler. On my ruler (suitable for the HQ Sweet Sixteen hopping foot), the half-inch lines near the inner edge of the slot are in effect 0.25 inch vertical lines. There are also some 45 degree lines.

You have several positioning choices when using this ruler:

  • place the slot vertical to your body position, then either pull the ruler and quilt towards you, or push it away from you
  • place the slot horizontal to your body (i.e. push/pull it to the left or right)
  • or some other angle of your choosing.

NOTE: If you are using the open-toe hopping foot, be careful if you’re trying to use the ruler at any angle other than vertical — the sides of the hopping foot need to touch the edges of the slot, and at non-vertical angles, that can be an issue.

If you look closely at the picture above, you’ll see other faint ‘lines’ — this is the cut edge of the ‘ClearGrip’ I have put on the underside of the ruler. ClearGrip helps hold the ruler in place on the quilt. (UPDATE: I now use small squares of Handi Grip on the underside of the ruler — it sticks the ruler to the fabric much better.)

I tend to use the ruler vertically, and slide the slot around the foot so that the open part of the slot is furthest away from me. I then pull the ruler (and quilt) towards me. But that’s me — you’ll need to practice to find out the best position for you.

I also use Machingers quilting gloves when using the ruler as it gives me better grip. In the photo below, you can only see my left hand as I used my right to take the picture! But I’d normally have both hands on the ruler, applying downward pressure with the heels of my hands, thumbs, and forefingers as I move the quilt and ruler towards or away from me. Notice that my third finger (left red arrow) is resting against the edge of the ruler. I do the same with my right third finger, and in this way I can adjust the position of the ruler as smidge if I need to as I’m stitching just by moving those fingers to the left/right as required. I think of this finger control like a horse’s bridle — with a well-trained horse, you only have to adjust the bridle a tad to the left or right to make the horse go where you want it to go. Or, if you’re not familiar with horses, think of power steering in your car — you only need to touch it a tiny amount to make small changes in direction. In the example below, I’d use my right finger to make a tiny leftward adjustment to the ruler so that I didn’t stitch over that point (right red arrow). Actually, I’d normally have made that adjustment a few stitches back. NOTE: In this photo I’m using light coloured thread, so I’d make any adjustments in direction in the light areas of fabric, not in the dark areas where they’d be noticeable.


In the picture below, you can see how I’ve lined up the ruler — the green arrows show the alignment of the centre line with the previous stitching and how the stitches just touch/skim the dark fabric points. The red arrows show another alignment method — placing the laser-etched lines parallel or on the seam lines. Of course, this will only be successful if the elements in the block are perfectly square ;-). Notice the area where the top green arrow is pointing — see how the hopping foot is snug against the edges of the slot? Sometimes, when you move the ruler to the next position, you can end up with it sitting on top of the hopping foot if you’re not watching carefully — if you stitched with it like that, you could damage your hopping foot, the needle, the timing of the machine, and/or the ruler!


The final picture (below) shows how I’ve lined up the stitching line so that it will go exactly in the centre of the slot. I eyeball this, and with some practice have got pretty good at ‘guessing’ where that stitching line will go. Again, the green arrows show the visual cues I use to align those points with the centre of the slot, and the red arrow shows the vertical line parallel to the block.



  • Rulers work best with the machine set to the ‘needle down’ position. If you have to make adjustments, you won’t have jumps in your stitches if you use ‘needle down’.
  • You only need to make small adjustments to change direction.
  • You need to apply downward and push/pull pressure to move the ruler and quilt under the needle.
  • Make sure the hopping foot is snug in the slot before you start stitching.
  • Use the laser-etched lines on the ruler as guidelines. You can line them up with seams, with other stitching lines (for an exact echo measurement), or with other elements on the quilt.
  • When stitching long lines, you don’t need to stitch the full length of the slot before adjusting the ruler. Stitch as far as you’re comfortable with (this might only be 4 or 6 inches), then stop. Adjust the ruler and start stitching again. With practice, you’ll be able to guide the ruler a smidge with your fingers as you’re stitching, but initially stop, then start again.
  • You WILL improve with practice! On my Sweet Sixteen, I can now stitch straight lines at 60-70% speed; when I first started using this ruler, I was going at about 15% speed.

Quilts I’ve stitched using this ruler:

Community Quilt 393

8 04 2018

As with most quilts, I started by stitching in the ditch around all the sashings and borders. For the centre panel, I stitched a square stipple; for the middle ‘circle’ of blocks, I stitched a square spiral in each; and for the outer ‘ring’ of multicoloured blocks, I stitched a big X, then lines sort-of echoing those Xs. I left the blue sashings and borders unstitched. I only used my Line Tamer rule for stitching in the ditch and the big Xs — everything else was free motion.

(Click on a photo to view it larger)

Threads used:

  • Top: Robison-Anton ‘Tuxedo Red’ (40 wt, rayon, colour 2420)
  • Bottom: Fil-Tec Magna Glide Classic pre-wound bobbin (candy apple red)


Community Quilt 390

5 04 2018

Someone had fun making this convergence quilt! Nice bright colours, and a pond scene.

But how to quilt it? As usual I started by stitching in the ditch around all the seam lines and borders, then decided to stitch horizontal lines about 0.5 inches apart in the main block with bright orange thread. I used my Line Tamer ruler for the stitch in the ditch straight lines, but just eyeballed the lines in between, so there’s not a true half inch between each. I did a similar treatment with the horizontal lines in the green borders.

In the purple borders, I stitched ‘u’ shapes, leaving the borders either side of the purple border unstitched. And in the orange border, I stitched a ribbon candy motif, also with bright orange thread.

(Click on a photo to view it larger)

Threads used:

  • Top: Fil-Tec Glide ‘Neon Orange’ (40 wt, trilobal polyester, colour 90811); Isacord (40 wt, trilobal polyester, colour 2900); Robison-Anton ‘Ming'(40 wt, rayon, colour 2322)
  • Bottom: Fil-Tec Magna Glide Classic pre-wound bobbin (light tan, lead gray)


Community Quilt 338

7 09 2017

This was a really big quilt, and my aim was to stitch the layers together in a way that held without going over the top with the quilting. I first stitched in the ditch around all the blocks, then simple straight lines (using my favourite Line Tamer ruler!) bisecting the blocks horizontally and vertically.

(Click on a photo to view it larger)

Threads used: (no information on threads as I did this quilt a while ago and can’t remember what I used!)



Community Quilt 316

18 04 2017

I really liked how the disparate fabrics in this quilt went so well together in the ‘sort of’ log cabin design. But how to quilt it? After stitching in the ditch around the main blocks, I decided to ditch stitch straight lines (using my indispensable Line Tamer ruler!) following the second log cabin seams surrounding the centre square, using a variegated yellow and teal thread. I extended these lines out into the border too. I very much liked the final, almost art deco, effect.

(Click on a photo to view it larger)

Threads used:

  • Top: Signature ‘St Thomas’ (40 wt, cotton, colour F151)
  • Bottom: Fil-Tec Magna Glide Classic pre-wound bobbin (white)


Community Quilt 292

3 09 2016

I’m not really a fan of these colours, but together I thought they worked really well. To keep with the simple shapes, I decided to quit vertically in the three strips on the sides, and horizontally for the three middle strips. Each line is about 1 inch apart. Yes, I used my Line Tamer ruler for this!

(Click on a photo to view it larger)




Threads used:

  • Top: Fil-Tec Affinity ‘Carolina’ (40 wt, trilobal polyester, colour 60292)
  • Bottom: Fil-Tec Magna Glide Classic pre-wound bobbin (white)


Community Quilt 243

24 11 2015

Compared to the most recent quilts I’ve done, this was a tiny one 😉

Again, a scrappy quilt, this time set off with yellow sashings and borders. As it was such a busy quilt, I decided to keep it simple, stitching wonky stars in each block (using my Line Tamer ruler) and mountains (or Vs or Ws) in the borders.

(Click on a photo to view it larger)



Threads used:

  • Top: Floriani (40 wt, rayon, colour PF546)
  • Bottom: Fil-Tec Magna Glide Classic pre-wound bobbin (light tan)


Community Quilt 240

24 11 2015

This big log cabin quilt was created with some lovely autumnal scrappy fabrics.

How to quilt it? I stitched in the ditch around the large blocks first, to stabilise it. Then countered the geometric nature of the log cabins with large spirals in a variegated thread, morphing into squared-off headbands, and then into open headbands. So there are three quilting motifs in this quilt. In the border I echo stitched a straight line (using the Line Tamer ruler) about half an inch from the seam line.

(Click on a photo to view it larger)






Threads used:

  • Top: Fil-Tec Harmony ‘Tweed’ (40 wt, cotton, colour 14076)
  • Bottom: Fil-Tec Magna Glide Classic pre-wound bobbin (light tan)


Community Quilt 231

18 10 2015

How to quilt this dramatic red and white quilt?

I agonised over how I would quilt it as I stitched in the ditch around ALL the blocks, eventually settling on doing a wonky star in red thread on the white crosses, and some very dense quilting on the ‘backgrounds’ to the red stars, thus creating a puffy square effect. I used my Line Tamer ruler for all the straight lines, except the dense quilting.

I thought about doing a white wonky star motif in the red squares, but decided against it as I quite liked the puffiness of those squares against the rest of the quilt.

I stitched straight ‘piano key’ lines in the tartan border, following the pattern in the fabric.

(Click on a photo to view it larger)



Threads used:

  • Top: Fil-Tec Glide ‘Cardinal’ (40 wt, trilobal polyester, colour 700001)
  • Bottom: Fil-Tec Magna Glide Classic pre-wound bobbin (red)


Community Quilt 212

24 05 2015

This was a HUGE scrappy quit, done in a fairly traditional style. In fact, I think a lot of the top was hand stitched. What an effort!

How to quilt it? Well, the obvious first step was to stitch in the ditch around ALL the blocks and borders, and the coloured fabrics in those blocks. This took a few hours, even with my favourite Line Tamer ruler.

I decided to leave the coloured blocks unstitched, except for the ditch stitching, so they’d ‘pop’. In the white space, I echo quilted about a half inch from the seams, then free-motion stitched large ribbon candy in the remaining spaces.

I did a similar treatment in the final white borders, leaving the inner white border and the coloured border unstitched (except for stitch in the ditch).

In total, this quilt took about 6 hours to quilt on my Handi Quilter Sweet Sixteen. It was big!

One of the photos below shows the quilting in progress — the area on the left is fully quilted; the area on the right is just pinned ready for stitching. You can see what a difference quilting makes.

(Click on a photo to view it larger)





Threads used:

  • Top: Fil-Tec Glide ‘Cream’ (40 wt trilobal polyester, colour 20001)
  • Bottom: Fil-Tec Magna Glide Classic pre-wound bobbin (white)